CISCO MDS 9124 CONFIGURATION GUIDE PDF

Home  /   CISCO MDS 9124 CONFIGURATION GUIDE PDF

Example Cisco MDS Switch Default Port License Configuration. switch# show port-license Available port activation licenses are 0. Cisco MDS Family Quick Configuration Guide. OL Using the Switch Setup Utility Verifying the Module Status CHAPTER. 3. Configuring. Note If a Cisco MDS or switch is used as a core switch, only a nontrunking F PortChannel is supported. Trunking is not supported on.

Author: Kigar Tauktilar
Country: Malawi
Language: English (Spanish)
Genre: Finance
Published (Last): 15 August 2010
Pages: 317
PDF File Size: 19.84 Mb
ePub File Size: 4.26 Mb
ISBN: 184-5-38129-118-4
Downloads: 48288
Price: Free* [*Free Regsitration Required]
Uploader: Tojagul

It is worded as if it is a requirement but it is in fact not. Proudly powered by WordPress. This is not true. The default authentication port is Page Figure shows incorrect ip default-gateway Page States in one bullet: Certainly there is either a mistake in the wording or the example. Although it can be configured it has no effect. You cannot mix ingress and egress interfaces in the same SPAN session.

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata

Caution The span drop-threshold can be changed only if no span sessions are currently active on the switch. This can mean several configuration tasks for each cico host. If a domain is currently isolated due to domain overlap, and you later enable the autoreconfigure option on both switches, the fabric continues to be isolated. I am not sure.

This situation can require several configuration tasks for each iSCSI host. FCIP uses different ports. There is no information contained in the example given that shows the configuration or guife of FCIP interfaces.

This page incorrectly states that you can disable password verification with aaa authentication login none command. Leave a Reply Cancel reply You must be logged in to post a comment.

  FRAKTUR KOMPRESI VERTEBRA PDF

You do not need to restart the fcdomain. In this case, using the proxy initiator mode simplifies the configuration. When you join two switches belonging to two different stable fabrics that have overlapping domains, the following cases apply: From time to time I will blog about other things of interest.

This however would be very nice to have in the documentation for IPS network simulator, an example showing complete configuration of Gigabit Ethernet interfaces and FCIP tunnels to go along with the Network Simulator.

This page incorrect states that fcns reject-duplicate-pwwn is disabled by fisco. These pages talk about an active mode of fcanalyzer. I am not sure that the statement in bold is correct. You basically give the same settings for the IBM blade switch but this is a 24 port not a 20 port.

I think what is meant here is: IP routing does not have to be enabled, unless there is a specific topology where IP routing is necessary.

This is very redundant and can be combined into one bullet.

The way its written sounds like if you have a large scale deployment where you configuuration explicit LUN access control you can use proxy-initiator, but its really the opposite. Previous blog entries also dealt with storage, compute, virtualization and professional services. The autoreconfigure option takes immediate effect at runtime. About System Message Logging properly configured system message logging server. Page shows with 8 base ports 8 licensed for growth.

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata – Maximum Entropy

This blog is mostly about my pursuits in Data Science. Have a few different people read that and I think you will see where I am coming from. Reconfiguration as in changing of domains is always disruptive. A disruptive reconfiguration may affect data traffic.

  GHIDUL INCEPATORULUI PENTRU CREAREA REALITATII PDF

I am not sure if this is valid. On the same page I find this block of text very vague and confusing: Should say Step 1 Enable the mgmt 0 interface. The opinions expressed in this blog are entirely my own and should not be taken as the opinion of my employer.

Testing indicates that this is in fact enabled by default.

Page Information is repeated twice on the same page: Obviously there was a part of this paragraph that got chopped off somewhere. If you do not need explicit LUN access control, using the proxy initiator mode simplifies the configuration. You can nondisruptively reconfigure the fcdomain by changing the configured domains on the overlapping links and getting rid of the domain overlap.

jds

You must be logged in to post a comment. Page Document states: This is not correct as this does not work. This is not correct. Then states two bullets later: If you assign port number for physical portshow can you assign for ports ?

Should be 8 base ports, which can goto 8 or 16 additional ports. This should be made more guuide. Cisco Documentation team has internally re-written this as: