View and Download D-Link DSLB user manual online. DSLB Modem pdf manual download. Don’t follow these instructions until you have received confirmation that your broadband service is ready to use. Have you got your broadband username. Section 1 – Product Overview. D-Link DSLB User Manual. 3. Package Contents. • DSLB ADSL Modem. • Power Adapter. • CD-ROM with User Manual.
|Country:||Central African Republic|
|Published (Last):||5 July 2018|
|PDF File Size:||5.86 Mb|
|ePub File Size:||8.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
Your network service provider will give you instructions about any additional connection software or NIC configuration that may be required. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. By pressing ‘print’ button you will print only current page. Linksys is a registered trademark or trademark of Cisco Systems, Inc.
The Router should not be located where it will be exposed to moisture, direct sunlight or excessive heat. All rights reserved No part of this publication may be reproduced, More information.
The default Username for the Router is admin. Manhal the computer is turned off, the link light may not be on. Click on the Next button to go to the next Setup Wizard window. Wait about 30 seconds and try accessing the configuration.
The Outbound Filter allows you to create a filter rule to block outgoing IP traffic by specifying a filter name and at least one condition below.
Please type the port number which you want to replace the original port. Manua it is necessary to reconfigure the device, all the necessary information can be easily accessed. Before you Begin Please read and make sure you understand all the prerequisites for proper installation of your new Router. Internet Steady green light indicates a successful Internet connection. Troubleshooting This chapter provides solutions to problems that might occur during the installation and operation of the DSLB.
The default mode is enabled. This provides Internet access to everyone in the office for the price of a single user. Unfortunately this process will change all your settings back to the factory defaults. Section 3 — Configuration Setup This section will show you how to set up and configure mnual new D-Link Modem using the Web-based configuration utility.
This can be adjusted according to the time of the day scheduling. In a domestic environment, this product may cause radio interference. Please use only wired network connections to configure the Router. If possible, you should be able to see the LED indicators on the front if you need to view them for troubleshooting.
The IP address can be assigned in a number of ways. When entering the IP address of the D-Link router Device Maual The Device Info page displays a summary dxl of your router status, including: If you do not get a solid link light, try using a 230b cable if possible.
Your network service provider will give you instructions about any additional connection manua, or NIC configuration that may be required. Please click the Save Settings button to 320 the configuration. The device has the utility built-in to a ROM chip in the device itself. From the Security tab, click on the button to restore the settings to their defaults.
Click on the Save Settings button to save the settings. Connect the micro More manul. Steady green light indicates a negotiation process has been successful Internet connection.
Firmware Update Save As window that immediately opens. Page 20 Click the OK button to proceed with the Modem reboot. Support Warranty Document Open support case. If you have a different operating system, the screenshots on your computer will look similar to the following examples.
The default Password is admin. Be sure that the cable connecting the LAN to the Router does not exceed meters. Follow standard Ethernet guidelines when deciding what type of cable to use to make this connection. Power down all your network devices, including your computer s and the Modem Router.
NAT improves network security in effect by kanual the private network behind one global and visible IP address. Use these windows to view system information and monitor performance.
Don’t show me this message again. Check the help files included with your firewall software for more information on disabling or configuring it. Features This eliminates the need to reconfigure every host 3220b changes in network topology occur.
This eliminates the need to reconfigure every host whenever changes in network topology occur. Manal you are using a low pass filter device, follow the instructions included with the device or given to you by your service provider.
Enter the authentication password Password: MDI-X ports 1x, 2x, etc. Remember that this will wipe out any settings stored in flash memory including user account information and LAN IP settings. The device settings will be restored to the factory default IP address and the subnet mask isthe default management Username is admin and the default Password is admin.
The default mode is disabled. Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of manuzl revisions or changes. Inform Interval seconds between two Inform Interval: