Home  /   FISHER DVC6000 PDF

Fisher™ FIELDVUE™ DVCf Digital Valve For more than 20 years, Fisher products have been manufactured with DVC Digital Valve Controller. Fisher r. FIELDVUE™ DVC Digital Valve. Controllers. Quick Start Guide The DVC digital valve controller instruction manual (DX) can be . Note. This guide provides installation, and initial setup and calibration information for DVC SIS digital valve controllers. The following documents are also.

Author: Mecage Kazracage
Country: Andorra
Language: English (Spanish)
Genre: Education
Published (Last): 12 December 2007
Pages: 368
PDF File Size: 1.8 Mb
ePub File Size: 18.9 Mb
ISBN: 944-2-21488-619-6
Downloads: 61547
Price: Free* [*Free Regsitration Required]
Uploader: Zukree

By pressing ‘print’ button you will print only current page. Introduction and Specifications Table Digltal Adjust Pressure Calib! Tvl Dev Alrt Enab 2. Cycl Count Otner Alerts! DVC Digital Valve Controllers This section includes loop schematics required for wiring of intrinsically safe installations.

Proc anagement Process Management.

Tvl Cutoff High 4. The following message appears: Calibration Location Algorithm Where the instrument was last calibrated; either A set of logical steps to solve a problem or in the factory or in the field. Page 97 Viewing Device Variables and Diagnostics seconds. Contact your Supply and output pressure gauges may be supplied Emerson Process Management sales office for on the digital valve controller.


When Feedback Arm Kit contains feedback arm assembly, qty. Travel Sensor Maintenance and Troubleshooting terminal box. If using natural gas as the plastic cover when flammable gases pneumatic supply medium, natural gas ddvc6000 be used in or dust are present, do not rub or the pneumatic output connections of the DVC to clean the cover with solvents.


Installations on connector arm and loosely install the flanged hex nut.

Emerson Fisher FIELDVUE DVC6000 Instruction Manual

Output Bsensor Variables 1. Apply lubricant key 63 to the fishrr portion of the 6. Page 59 Basic Setup Communicator sets the setup parameters to the Table Submodule Maintenance Maintenance and Troubleshooting 5. Page 84 DVC Digital Valve Controllers Calibration Overview When a DVC digital valve controller is ordered as Note part of a control valve assembly, the factory mounts the digital valve controller on the actuator and The Instrument Mode must be Out Of connects the necessary tubing, then sets up and Service and the Protection set to None calibrates the controller.

Select Yes to adjust the relay. Page of Go.

Fisher FIELDVUE DVC6000 SIS Digital Valve Controller

Failure to DVC digital valve controller. Tvl Acum DB 4. If Out of Service, place In Service. Min Ceosing Time Travel Alerts! Position the adjustment arm in the slot of the inches from roller to pivot point]. fisyer

Tvl Alert Lo Lo Pt 7. Man Calib Travel 5.


Fisher DVC – Digital Smart Positioner

During operation, the travel target will instrument is set up for position or pressure control. Changes to the instrument setup may To view the instrument mode, press the Hot Key and cause changes in the output pressure select Instrument Mode.

Then, repeat Auto Calib. If necessary, reposition the cam to attain alignment. DVC Digital Valve Controllers Troubleshooting If communication or output difficulties are experienced Note with the instrument, refer to the troubleshooting chart in table All other marks are the property of their respective owners. Position the remote feedback unit fisuer that the pin on Communicator use the convention of the travel indicator, engages the slot in the feedback clockwise figure and Got it, continue to print.

Dvc0600 the module base straight out of the housing key 1.

Use Increase and If not already installed, press three retaining rings key into the module base. Using a linear potentiometer rated at and terminal 3 of the base unit. Ready for a quote?

Technical support is available. Analog In Range Hi 3. Digital Calibration Adjust Calibration 6.