To make it even easier, JACO also sold plans for a filing fixture that Two more Jaco pistols: the JACO Western Pistol and the JACO Derringer. Maadi griffin pdf blueprints – griffin pdf blueprints to JACO Derringer Pistol Blueprint SIG P Pistol. Machinist Drawings for SMG gun. JACO offers a hot bluing technique that is comparable in appearance and durability to those on factory made guns. The plans show the position and function of.

Author: Madal Dobei
Country: Brunei Darussalam
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 18 February 2008
Pages: 297
PDF File Size: 8.79 Mb
ePub File Size: 17.90 Mb
ISBN: 392-6-17312-392-1
Downloads: 26736
Price: Free* [*Free Regsitration Required]
Uploader: Meztile

It is important that the wood fits the Vee notch in the side plates.

Wire brushing after smooth filing makes a good servicable surface for a blued gun to be used in the field. Place hammer in its proper position in the frame making sure that the front face of the hammer is flat against the breech block. After epoxy cures, file excess liner square with barrel.

homemade derringer

verringer This pistol breaks open to load naco clean and is latched rigidly closed with a spring loaded cross bar mechanism. Insert trigger spring and stake in location by center punching. Critical dimensions such as at trigger sear, hanmier sear notches, latch and extractor should be left oversize and finished at assembly. Clean gun thoroughly with solvent and oil with gun oil. The spring back will provide the right preload for the latch. Complete the latch work on the frame as indicated on the side plates.

In finishing, it should be remembered that derrinter gun traditionally has square corners that are broken slightly to eliminate sharpness. Note the location and place hammer on the outside of frame in the exact position as it was inside the gun and damn.


JACO has developed a hot bluing solution that can be accomplished on the kitchen stove ancJ’ provides good a surface that can be obtained commercially. You may alter the design to suit your own preference in some areas like a longer barrel or a thicker handle. Reading do have alook at this link http: Carefully file sear and notch so that they derringsr engage.

Search the history of over billion web pages on the Internet. Epoxy in indicated position. Slide barrel into frame so that breech is against breech block and properly positioned. Full text of ” Derringer Pistol Check gun for correct operation of latch extractor, hammer and trigger using fired cases.

OIA incii from the side of the front sight for every inch to be moved on the target. Use epoxy cement or soft solder to secure liner to barrel.

The Casual Shooter: DIY Firearms

These can be cut out or traced and pasted on the steel stock to assist in cutting the pacts. AK 47 Receiver Blueprint. This allows the use of soft steel in the hammer and trigger. Hand Gun Blueprints And Construction gun derrigner, gun Get Maco Know Us.

Drill the latch pin hole in the same manner, through the assembled barrel and frame. Insert a rivet to main- tain this rerringer and proceed to drill the remaining three holes in like manner. Do as you wish with these drawings included are two versions of detailed drawings for the colt These drawings are freelyavailable on the. Burt the handle against the base plate and clamp to side plate.

Separate details are drawn for each part. These plans and instruc- tions may not be copied in whole or in part without written consent of JACO Designs.

Because we have no control over Che materials you use, Che workmanship or possiblt? Bend spring back slightly to increase trigger pull force.


Dis- assemble and complete the latch pin slot by sawing and filing the barrel block. Excess round- ing of edges is not accepted gun practice. Enlarge hole with a No. Cut out the hammer sloe and file the notches for the hammer spring rest.

Drill and pin with rivets as before. Stretch and compress spring as before With Hammer Spring Guide 3 assemble above items into handle of pistol as indicated.

The gun can be derrinyer with any of the cold bluing products but these tend to produce a superficial coating that is not very durable.

my newest rimfire, one of a kind!

The plans show the position and function of all parts. The hole should then be enlarged to the size required to fit Che rifled liner you purchase. Be sure to allow extra turns for some spring back.

Remove all surface rough- ness that would marr the appearance of the finished gun. Most of the material re- quired is cold rolled steel CRS.

I have blueprints for a lot of firearms. File extractor to final shape except where it will be chambered and assembled in barrel. Cut in half to form box and lid. Repeat process for the other side plate. The Latch Spring 11 is made by winding 21 coils of 0.

Wind Hammer Spring 4 using same procedure as before. Do as you wishwith these drawings included are two versions of detailed drawings for the colt These drawings are freely available on the. Karakhamun was a Kushite and a plan of his tomb was made in but it did not.